Discovering Plumbing Basics is Crucial for Installing a Bathtub
Discovering Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
The author is making a few great pointers about Installing A Bathtub as a whole in this article down the page.
Installing a bathtub isn't exactly rocket science, but it does need solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old bathtub is conveniently available, the job can move easily; if you have to open a wall to eliminate the old tub and position the new tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will require a helper to move out the old tub and also set in the new one. Ensure you have actually qualified yourself for the task and are comfortable trying it. Instead of working with a professional to take over a halfway-completed task, it is better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube links.
This article will certainly aid you install a new bathtub in your restroom if you have already bought a new tub as well as don't require to alter the setup of your previous water supply pipes.
Your devices and product checklist must make up the following:
Preparing for the Installation
First of all, the sustaining structure supplied with the bath ought to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to stop pressure on the tub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its final placement.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome because of the limited access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old sealing compound.
Before going on to fit the brand-new taps, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, put the bathtub in the needed placement. The wood boards are handy in uniformly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the level and also changing the feet on the bathtub up until the spirit level checks out level.
To install taps, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system and examine all joints and also new pipework for leakages and also tighten them if needed. Fill the bath tub and additionally examine the overflow electrical outlet and the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling and sealing around the bath tub must wait until the bathtub has actually been used at the very least when as this will certainly resolve it into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap ports. The former kind must be connected to the tap finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to fracture a stiff seal, causing the water to penetrate the wall between the bath and also the tiling, leading to complications with dampness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and also fittings. They are sold in tubes and also cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture relatively early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on Installing A Bathtub? Make a comment directly below. We will be interested to know your responses about this post. In hopes that you come back again in the near future. So long as you liked our post if you please make sure you remember to pass it around. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
No more leaks, call us! Report this page